Desolder/Solder Gel Flux - 10 gr Smooth Flow Tack Flux NO CLEAN Hot Air...
Gravity : Measurement of pH of a solution 0 to 14 pH (+/- 0.1 pH) Gain...
Soldering Flux - Gel - 10 gr High quality, High fluidity NO CLEAN Hot...
Motors control board for Raspberry-Pi Pico 4 DC motor 2 stepper motor 8...
MD2 drone Kit to assemble (Learning and Makers) Repairable Payload:...
Air:bit - Drone for Micro:bit Real time measures Code Bloc programmable...
Backplane prototyping board DIN case: 6 modules Level: Backplane...
The microcontroler usually needs some help when they need to control motors. This is because the motors are consuming lot of current (or power) and that microcontroler are not taillored for such amount of current.
Thankfuly, they are Motor Controlers! They can be as simple as L293, L298 or more advanced board, the motor controler are there to ease your life by taking care about all the stuff related to motor power control.
With thoses board and breakouts you will ba able to tame DC motors, stepper motors, servo motors, etc. All you need to motorise your project and made it autonomous in our human world.
Motor Shield + selection of V2 motor. A great pack to start experimenting motors with Arduino.
Double H-Bridge L298N to control motors: 2 motors, 2 directions of rotation, speed control
Step-by-step motor controller A4988 - micro-step Motor voltage: 8 à 32V Motor current: 1.2A (2.3A in peak) Micro-stepper: 1/16 of step max. Current limiter Logic: 3.3 et 5V
DRV8825 stepper motor controller - micro-step, high current
This product is being translated Contrôleur moteur pas-à-pas DRV8834 - micro-step, courant élevé
MP6500 stepper motor controler Micro-stepping 1/8 step max Motor 4.5V to 35V Current 1.5A (2.5A peak) Logic 3.3v - 5v Current limiter
Step motor controler TMC2208 A4988 compatible Silent Stepstick MicroStepping: 1/256 step max Motor voltage: 5.5V à 36V Motor current: 1.2A per coil (2A peak) Logic level 3.3 and 5V Current limiter
Stepper controleur 36v4 - micro-stepping MicroStepping: 1/256 step Motor voltage: 8 - 50V Logic: 1.8V, 3.3V & 5.8V Motor current: 4A Max per coil (6A peak en pointe) Configurable via SPI STEP/DIR control (or full control via SPI) Based on DRV8711 + external MOSFET
This product is being translated Contrôleur de moteur pas-à-pas AMIS-30543 - 3A - 6-30v - micro-step
DRV8833 controler - double H-Bridge 2 DC Motors 1.2A (2A current peak) 2.7 to 10.8V
HAT PWM / Servo - 16 channels - for Raspberry Pi
Allows to control up to 16 servo motors (or LEDs) in PWM. Can be connected in series to obtain 32,64,128, ... channels and up to 62 x 16 channels with only 2 interface wires!
HAT control driver continuous motor and stepper motor
Robotic + microcontroler board 32u4 - Arduino Leonardo compatible Motor: 6-23V DC 2x DC Motor (2A) or 1 Stepper XBee connector APC220 connector microUSB connector Also known Romeo V2 / DFR0225
Crickit - Creative Robotics & Interactive Construction Kit for Micro:bit MakeCode and Arduino support 4x Servo Motor driver -OR- Analog output (PWM) 2x DC motor driver (with PWM control) 4x high curent output (relay, solenoid, etc) 4x capacitive touch entry 8x digital I/O (or analog inputs) 1x LED NeoPixels 5V driver (wired on pin #16) 1x Amplified...
Crickit - Creative Robotics & Interactive Construction Kit for all the les Feather MakeCode, Arduino, CircuitPython interface I2C 4x Servo Motor controler -OR- Analog 2x DC motor controler (PWM) 4x Power output (relay, solenoid, etc) 4x Capacitive input 8x digital I/O (or analog input) 1x NeoPixel LED controler 1x Audio amplifier (selectable pin)
Motor expansion board for MicroPython Pyboard - Basic kit
Motor expansion board for MicroPython Ultrasonic detector detector 5V regulator L293D based dual H-Bridge based motor
This product is being translated Pilote 2 moteurs - DRV8835 - pour 2 moteurs
Gravity : Continuous motor controller 2 motors (in both ways) Logic : 2.7 to 5V Motor : 2.5 to 12V Current : 1.2A (2A in impulsion)