The Raspberry Pi 3 - even faster than the Pi 2, 1 Giga of RAM, WiFi...
Assortment of BreadBoard wires Female-Female 300mm and 75 mm + Long...
Prototyping and e-learning platform for creating interactive objects or...
2 heat sinks + adhesive - high performance, for your Raspberry-Pi
Hall effect sensor - Sensitive to magnetic fields
Manufacturers
Raspberry-Pi Pico Microcontoler RP2040 Cortex M0+ @ 133 MHz, 2 cores 2...
Raspberry-Pi Pico Microcontoler with header soldered RP2040 Cortex M0+ @...
IoT development kit based ESP32-Pico ESP32-Pico @ 240Mhz Flash 4Mb Ram...
HUB Module for Atom- Advanced prototyping Industrial proto board (Grove...
DIY proto module for Atom Simple proto board Case Connector 3.96 A077
ESP32 Atom development kit + MATRIX M5Atom lite ESP32-Pico-D4 @ 240 Mhz...
ESP32 ATOM development kit + BARCODE M5Atom lite ESP32-Pico @ 240 Mhz...
PYBStick interface for Adafruit's FeatherWing expansion Feather port -...
Raspberry Pi 4 4Go KIT - the ALL-IN-ONE keyboard! Power Supply HDMI...
Raspberry Pi 4 4Go KIT - the ALL-IN-ONE keyboard! Power Supply HDMI...
Viewed products
Audio Amplifier Stereo 2x 3.7 Watt...
AMP-3.7W-CLASSD
ADA987
Audio Amplifier
In stock
Availability date:
2x 3.7w amplifier - MAX98306 - Class D
Audio Amplifier
Recipient :
* Required fields
or Cancel
This small stereo amplifier is incredibly powerful - capable of delivering 2 x 3.7W on its channels equipped with speakers (impedance 3 Ohm). Ce petit amplificateur stéréo est incroyablement puissant - capable de délivrer 2 x 3.7W sur ses canaux équipés de haut-parleurs (impédance 3 ohm ).
Inside the miniature integrated circuit is a controller class D, able to work with a voltage of 2.7V to 5.5V continuous. L'intérieur du circuit intégré miniature contient un contrôleur de classe D, capable de fonctionner avec un tension de 2.7V à 5.5V continu.
Since this amplifier is Class D, it is incredibly efficient (up to 90% when it drives a speaker of 8Ω at more than 1 Watt). It is thus a perfect tool for portable projects and/or working on battery. This circuit contain a thermal protection and short-circuit but pay attention because it can be very hot! Comme cet amplificateur est de classe D, il est incroyablement efficace (plus de 90% lorsqu'il pilote un haut-parleur de 8Ω à plus d' 1 Watt). C'est donc un outil parfait pour les projets portable et/ou fonctionnant sur pile. Ce circuit contient une protection thermique et de court-circuit mais attention car il peut devenir vraiment chaud!.
This card will be a good "upgrade" to replace a basic amplifier type "LM386"! Cette carte sera un très bon "upgrade" pour remplacer un ampli de base type "LM386"!
The inputs of the amplifier passes capacities of 1.0µF, this are inputs totally 'differential' - if you don't have differential outputs to connect to the inputs of the amplifier, simply connect L- and R- to the ground. Les entrées de l'amplificateur passe pas des capacités de 1.0µF, c'est donc des entrées totalement 'différentielle' - si vous ne disposez pas de sortie différentielles à raccorder sur les entrées de l'ampli, raccordez simplement L- et R- à la masse.
The outputs are "Bridge Tied" type (see here) - this means that the charge (speaker) is connected between two amplifier outputs, no connection on the ground - doubling as well the voltage to coils... which quadruple the power (cfr glossary of Maxim integrated). Les sorties sont de type "Bridge Tied" (voir ici) - cela signifiant que la charge (le haut parleur) est branché entre deux sortie d'amplicateur, pas de connexion à la masse - doublant ainsi la tension aux bobines... ce qui quadruple la puissance (cfr glossaire de Maxim integrated).
The output is a PWM square wave of 360 KHz that is than balanced ('averaged out') in the speaker coil - high frequencies are not audible. La sortie est une onde carré PWM de 360KHz qui est ensuite équilibrée ('averaged out') dans le bobinage du speaker - les haute fréquences ne sont pas audibles.
Therefore, which describe above involve that you can't connect outputs to another amplifier, the outputs should directly drive speakers! Par conséquent, ce qui décrit ci-dessus implique que vous ne pouvez pas connecter les sorties sur un autre amplificateur, les sorties doivent directement piloter des haut-parleurs!
The breakout board is delivered completely assembled and tested with inputs capacities of 1.0µF. We also include a PinHeader which allows to connect this card directly to a breadboard. Le breakout board est livré complètement assemblé et testé avec des capacités d'entrées de 1.0µF. Nous avons également inclus un pinHeader permettant de raccorder cette carte directement sur un breadboard.
3.5mm screw terminal blocks are also included to allow easily connection of speakers. Des borniers à vis de 3.5mm sont également inclus afin de permettre de raccorder facilement des haut-parleurs.
Finally, the 2x4-pin PinHeader and the jumper allows to change the gain to the fly. Finalement, le pinHeader 2x4 broche et le cavalier permette de changer la gain à la volée.
This breakout will be ready to use in less than 15 minutes! Ce breakout sera prêt à l'emploi en moins de 15 minutes!
Speakers not included! Use speakers with an impedance of 3 Ohms or more. Haut parleurs non inclus! Utilisez des haut-parleurs avec une impédance de 3 Ohms ou plus.