WiPy - MicroPython WiFi...
25 Max. per order Raspberry-Pi Pico Microcontoler RP2040 Cortex M0+ @...
The Raspberry Pi 3 - even faster than the Pi 2, 1 Giga of RAM, WiFi...
Assortment of BreadBoard wires Female-Female 300mm and 75 mm + Long...
MAX PURCHASE 1 or 2 per person during global component back-out period...
MAX PURCHASE 1 or 2 per person during global component back-out period...
Manufacturers
2.2" TFT display Breakout 240x320 pixels 16 bits colors SPI Interface...
Wiring cable 150mm JST-SH 4 poles, 1mm to Male pins StemmaQT Qwiic
Wiring cable 50mm JST-SH 4 poles, 1mm StemmaQT Qwiic
Polyimide Tape - AKA Kapton Wide: 10mm Length: 33m -269°C to +400°C
Cascade Resistors kit Best ratio tolerance / precision / price 10 Ohms...
Kit Cansat EU based on official Raspberry-Pi PicoMicroPython (default)...
Acces portal for Micro:Bit Servo-motor Piezo-buzzer
HAT UPS - Uninterruptible Power Supply Output: 5V 2.5A Output: 5V USB...
Mini Spy Camera for photo & vidéo Picture: 1280x720 px, JPEG Video:...
Mini GPS PA1010D (MTK3333 chipset) Patch Antenna GPS, GLONASS, GALILEO,...
Viewed products
TFT 10'' IPS - without frame, for...
TFT-HDMI-10pc-IPS
TFT 10'' IPS - without frame, for panel mounting
In stock
Warning: Last items in stock!
Availability date:
Create a nice audio/video display with a 10.1" IPS screen with HDMI stereo speaker support.
This screen would be great for video where it offers a bright 10.1" TFT display and a high resolution. The best is the great angle-visibility offered by the IPS technology!
This screen would be a great option for computer based projects as it is the thinnest, brightest, highest resolution display found for 10" diagonal. This "raw" display with mounting pad can be used to create a tablet or ultra flat solution.
The kit includes a driver board supporting various entries like HDMI, VGA, composites (NTSC/PAL) together with stereo output for 4 ohm (3W) speakers. The board auto-detect which input is used and automatically switch to it -OR- you can also use the OSD menu to select it manually. Putting it to work is fairly easy - simply connect the power supply (9 to 12VDC, 2.1mm jack center-positive) before connecting the video source to one of the ports. Don't forget to connect the speaker s to the SPK output pins... TaDaaa we have a gorgeous display!
The kit also includes an extra button board to activate the On Screen Display giving access to configuration like brightness, color and contrast. It also includes the plug-in cable to connect to the 4 pins of speaker output (labeled LOUT+/- and ROUT+/-) solder them to your own speakers.
Please note that it will not work with a device that only outputs DVI (you will need a DVI to HDMI converter), it will not work either with SECAM. Not HDCP compatible - it cannot be used with 'secured' HDMI sources.
The display, the control board and some cables.
The power adapter and speakers ARE NOT included, stand, Raspberry-Pi and other items are not included.
You will need a 9V or 12VDC adapter (also available on this shop)
This screen has been tested with a Raspberry Pi but will also work when connected to any HDMI, VGA or NTSC/PAL device.
IF the resolution is not auto-detected properly THEN you can edit your "config.txt" file to set the HDMI to 1280x800.
# All overscan_xxx are commented
# framebuffer_width and framebuffer_height are under comment
hdmi_force_hotplug=1
# uncomment to force a specific
# HDMI mode Group 2 and Mode 28 is 1280x800 @ 60hz
hdmi_group=2
hdmi_mode=28
hdmi_drive=2
Current draw: