This product is being translated WiPy...
15 ScrewDrivers Philips Plate Torx
Springton Prototyping Hat for Raspberry-Pi For Raspberry-Pi For PYB405 (...
32 GB card pre-formatted with Noobs - for Raspberry Pi 4, Pi 3, Pi 3 B+
Fan for Raspberry-Pi Silent... for real! Low consumption
Nut holder & foot M2.5 H: 5mm D: 10mm 4 pieces, white
Antenna connector, Plug Type: MCX RF Impedance: 50 Ohms Insulation:...
Multi-bands antenna GSM/GPRS (2G), UMTS (3G), LTE (4G) Gain 3dBi µFl...
HAT module GSM/GPRS for Raspberry-Pi SIM800C (GSM/GPRS) 2G, Antenna...
Prototyping HAT/pHat for Raspberry-Pi Stacking Header GPIO replicated...
HAT module GSM/GPRS for Raspberry-Pi SIM800C (GSM/GPRS) 2G, Antenna sticker
HAT module GSM/GPRS/BT for Raspberry-Pi SIM800C (GSM/GPRS) 2G, Bluetooth...
Translucent case (frosted effect) for Odroid N2
A breakout board is a experimentation board/PCB which offers access to component's internal signals, pre-assembled systems or high density components signals. Thank to the breakout boards, you can use components like (ex: BME280) and other component that, otherwise, would be impossible to use for makers and hobbyist. With breakouts, you can easily use RTC clock, SD card reader, TFT screen in your electronic projects.
Quad-band pour réseau Européen GPS Voice / SMS GPRS data AT command interface Native USB support
10 x breakout for 5050 LED (Neopixel)
Play audio file MP3/WAV/MIDI/OGG Record audio Micro-SD connector Jack audio output (and breakout)
Configurable Timer (with Potentiometer) Actived once every 100ms a 2 hour Reset Enabled (to restart the timer after job done).
Wide range of capabilities breakout 3 x 12-bit ADC inputs 3 x 8-bit PWM outputs 7 x GPIO with selectable pullup or pulldown 1 x NeoPixel output (up to 340 pixels) 1 x EEPROM with 64 byte of NVM memory (handy for storing small access tokens or MAC addresses) 1 x Interrupt output that can be triggered by any of the accessories 2 x I2C address selection...
GamePad board with Gameboy's style. 2 Pads 4 boutons Bouton Start/Select Connexions bumpers Prêt pour GPIO Raspberry Pi
Temperature Humidity Barometric pressure VOC Gaz Interface: SPI or I2C
MiCS5524 Breakout CO Alcohol VOC Analog output
Breakout CCS811, gas sensor: equivalent CO2 + VOC gaz NTC thermistor I2C interface 3.3v and 5V ready
I2C Mono amplifier suited for Raspberry Pi 2.5-5.5V 3W Mono (left+right/2) 4-8 Ohms I2S interface
Tranform a power cord or multi-plug socket into a microcontroler's controllable power plug.
D27V90F5 Switching DC-DC regulator, 5V 9A, Step-Down Output voltage: 5V (and possibility to configure lower) Input voltage: 38V max Output current: ~9 A max
D27V50F5 Switching DC-DC regulator, 5V 5A, Step-Down Output voltage: 5V (and possibility to configure lower) Input voltage: 38V max Output current: ~5 A max
Color TFT breakout Diagonal: 2.2" Coulor: 18 bits (262144 shades) Connector: microSD bus: SPI Ready 3.3 / 5V Driver: ILI9340 or compatible Breakout
RFM69HCW at 433Mhz SX1231 based module with SPI interface 50mA to 150mA ~30mA during active radio listening. Packet radio with ready-to-go Arduino libraries Uses the amateur or license-free ISM band (ITU "Europe" license-free ISM) Use a simple wire antenna or spot for uFL or SMA radio connector 500m to 2Km, even 5 (depending on the Antenna)
USB 2.0 Type-C female connector Breakout board
USB Servo controller for servo motor Maestro Mini from Pololu 12 channels 8 KB memory (3000 servo positions) Configuration Software, Autonomous script, USB-Serial script, TTL serial Arduino library & SDK